Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Kitchen Remodeling: The San Francisco Owner’s Guide
A full Tamko-focused kitchen remodel in San Francisco typically runs $16,520 to $53,100 installed, depending on cabinet run length, countertop material, and whether walls or plumbing move. We stock and install Tamko-compatible cabinet lines, trim, and hardware, and we can usually begin tear-out within a week of your written estimate. Most San Francisco homeowners call us after one specific thing fails: cabinet box corners pulling apart, warped doors from decades of fog humidity, or laminate edging peeling at the sink run.
If you’re reading this, you’re probably holding a hinge that stripped out of a particleboard panel, or staring at a drawer face that no longer closes square. That’s the reality of a Tamko kitchen that’s outlived its original install. Our job is to tell you exactly what’s worth saving, what gets replaced, and what the bottom-line number is before you sign anything.
Key takeaways:
- Installed Tamko kitchen remodeling in San Francisco: $16,520 – $53,100.
- We’re an independent contractor, not affiliated with Tamko, but we work with Tamko cabinetry and components every month.
- Every project gets a written price before work starts, and a 365-Day Done Right Promise in writing at close-out.
- Call (831) 610-5598 for a free estimate. A live person answers, 24/7.
Which Tamko Models This Applies To
Tamko’s kitchen lines changed hardware specs a few times over the years, and that’s where most San Francisco owners get tripped up. Older Tamko runs used 35mm cup hinges with a 9mm inset, while newer lines shifted to a 12mm inset on soft-close hardware. If you order the wrong hinge pattern, the door hangs proud of the face frame by enough to annoy you every single day. We measure before we order, every time.
On the OEM versus aftermarket question: Tamko’s original cabinet boxes are typically 1/2-inch furniture board with a melamine interior. Quality aftermarket drawer slides and hinges from Blum or Salice often outlast the original Tamko hardware, and we’ll tell you when that’s the smarter spend. For doors and drawer fronts that aren’t warped, refacing with new veneers works. For boxes that have taken moisture in the sink base, replacement is the honest call.
We also stock and install parts for KraftMaid, Cambria, and Silestone kitchens, so if your Tamko remodel includes those surfaces, we’re already set up to match them.
Styles & brands we work with
Signs Your Tamko Kitchen Remodeling Is Failing
- Doors won’t stay closed or bounce back open. The hinge cup has worn or the mounting plate screws stripped out of the particleboard. This is the most common Tamko failure we see in San Francisco, especially on high-use sink cabinets where humidity weakens the board over time.
- Drawer faces sag or rub against the cabinet below. The slide’s ball bearings are shot or the drawer box corner joints have loosened. You’ll notice the drawer needs a hard push to seat fully.
- The sink base cabinet floor is soft or discolored. This is water damage working through the seam between the sink cutout and the cabinet deck. In San Francisco’s damp climate, even a small drip compounds quickly and the melamine starts to swell.
- Laminate edging peels at the counter front edge. The heat-seal bond failed, and now moisture gets behind the edge banding. Once it starts, it won’t stop on its own.
- Cabinet doors hang crooked even after hinge adjustment. The box itself has racked, meaning the corner joint failed inside the cabinet frame. That’s structural, not a hinge problem.
Replacement Cost & What’s Included
For a San Francisco kitchen remodel built around Tamko-compatible cabinetry, expect:
- Full kitchen remodel: $16,520 – $53,100
- Small kitchen remodel: $10,620 – $23,600
- Cabinet installation only: $4,720 – $15,340
- Countertop installation: $2,360 – $7,670
What drives the spread is linear feet of cabinetry, countertop material choice, whether you’re moving plumbing or electrical rough-ins, and the condition of the substrate under the old Tamko install. Every estimate we write gives you a line-item breakdown: materials, labor, disposal, and finish work. No lump-sum mystery number. The price we write is the price you pay, no change orders unless you change scope. And all of it carries the 365-Day Done Right Promise: if it fails within a year, we come back and fix it at no charge.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely check a few things yourself: tighten hinge screws, check if a door just needs a new bumper pad, or identify which side of the drawer slide is binding. Those are five-minute checks and they’re worth doing before you spend a dime.
Where DIY goes wrong on a Tamko kitchen is the cabinet box repair. Particleboard once it’s swelled will never hold a screw the same way again, and drilling into it with a bigger fastener just buys you a few weeks. Rebuilding a failed base cabinet so it carries a granite or quartz countertop safely is load-bearing work. Get that part wrong and you’re not just out a drawer, you’re risking a countertop seam cracking. That’s the point where calling a crew that does this every week saves you real money. Call (831) 610-5598 and we’ll give you a straight answer on what the repair actually needs.
FAQs
A Tamko kitchen installed in a San Francisco home typically lasts 15 to 20 years before cabinets show real wear, but the fog-belt neighborhoods like the Outer Sunset and Richmond District shorten that if the home lacks forced-air circulation. Humidity is the quiet killer of particleboard cabinets, and we see sink bases fail years before upper cabinets do.
Yes, if the cabinet boxes are still square and dry, we can replace hinges, slides, drawer boxes, and reface doors rather than tear everything out. If the base cabinet has water damage or the corner joints have racked, replacement of that specific cabinet is the better investment. Call (831) 610-5598 and we’ll tell you which path your kitchen actually needs.
A full Tamko kitchen remodel in San Francisco typically takes 3 to 6 weeks from tear-out to final walk-through. Cabinet-only replacements run faster, usually 1 to 2 weeks, depending on lead time for the door and drawer front order.
We keep common Tamko-compatible hinges, slides, and drawer box components on the truck for repair calls, which means most hinge and slide failures get fixed in one visit. Full cabinet replacements are ordered to spec after we measure, and we’ll give you the lead time on your written estimate.
Get Your Straight Number in San Francisco
If your Tamko kitchen is failing, you don’t need a sales pitch. You need someone to look at the cabinet boxes, tell you what holds and what doesn’t, and put the price on paper. Call Curtis Lane and the crew at Bradford Remodeling Co San Francisco at (831) 610-5598 for a free estimate. Straight number, real scope, no surprises at close-out.
Written by Curtis Lane, Owner, Bradford Remodeling Co – San Francisco, CA at Bradford Remodeling Co San Francisco, serving San Francisco and nearby areas.
