KraftMaid Fence Installation Nationwide

KraftMaid Fence Installation: The San Francisco Owner’s Guide

We install and replace KraftMaid fence systems throughout San Francisco, with most complete installations running between $4,130 and $10,620 depending on linear footage, substrate conditions, and whether we’re pulling an old fence first. We stock common KraftMaid fence hardware and components on our trucks, so most jobs don’t wait on a second trip. The typical call we get starts the same way: a gate that won’t latch after a rain, a post that’s listing toward the sidewalk after a winter storm, or panels that have started to cup and separate at the seams.

Call (831) 610-5598

KraftMaid is better known for cabinetry, but their fence line – spec’d through their outdoor products division – uses the same discipline: modular panels, powder-coated aluminum rails, and post systems designed to be set and forgotten. San Francisco’s damp, salt-air climate tests every fence hard. We’ll get into what fails and what it costs to put right.

Key Takeaways

• Installed price range in San Francisco: $4,130 – $10,620, written before any work starts.
• Most common failure: Post movement from saturated clay soil around the Sunset, Richmond, and Mission districts.
• What we stock: KraftMaid post caps, rail brackets, gate hinge kits, and panel clips; full panels are ordered to spec.
• Warranty: Every installation carries the 365-Day Done Right Promise in writing.
• Safety: Tensioned gate hardware and concrete-set posts are not a safe weekend DIY project.

Which KraftMaid Models This Applies To

KraftMaid’s residential fence product line breaks into two families: the Modular Series (pre-assembled panels, 6-foot and 8-foot sections, 4-foot to 6-foot height options) and the Post-and-Rail Series (loose components, mixed materials, longer runs). Most San Francisco installations are the Modular Series, often the 6-foot privacy configuration, because it handles wind load better on exposed lots in the Outer Sunset and the hills around Twin Peaks.

Here’s the compatibility gotcha worth knowing: KraftMaid fence panels from the Modular Series use a proprietary rail-to-post bracket. A standard generic bracket from a big-box store will not seat correctly and leaves the panel floating off the post by roughly a quarter inch. We’ve seen homeowners fight these brackets for an afternoon before calling us. The part numbers are stamped on the inside of the rail channel, near the post, and on the underside of the panel’s top rail. Bring us that number or a photo of the stamp, and we’ll match it to the right bracket, the right post cap, and the right hardware before our crew ever rings your doorbell.

For components, we default to OEM where the part affects structure – posts, rails, hinge hardware. For caps, trim pieces, and decorative inserts, quality aftermarket equivalents from our documented parts suppliers hold up and often cost 20-30% less. We’ll show you both options with prices in writing, and we’ll tell you which one we’d use on our own fence. Bradford Remodeling Co San Francisco is an independent service provider, not affiliated with KraftMaid. We’re simply a local crew that has installed enough of their product to know what works in this climate and what doesn’t.

Signs Your KraftMaid Fence Installation Is Failing

• Posts leaning more than 5 degrees. The concrete footing has shifted in San Francisco’s shrink-swell clay. The fog cycle around the Richmond District saturates the soil six months a year; when it dries, the clay shrinks, and the post loses bearing. A leaning post is a structural failure, not an appearance issue.
• Gate won’t latch or scrapes the ground on the swing. The gate’s hinge brackets aren’t the problem on KraftMaid modular fences – it’s usually the post the gate hangs from, slowly rotating under the gate’s weight. Straightening the gate without addressing the post buys you six months.
• Panels cupping, splitting, or rattling in the wind. Salt air, fog moisture, and UV exposure age San Francisco fencing faster than most people expect. Once a panel’s edge seal fails, the wood or composite core starts taking on water, and the panel swells out of the rail.
• Rail brackets pulled loose from the post. This is the proprietary-bracket failure we described above. Usually a sign someone used hardware-store clips or the installer overtightened an aluminum bracket and stripped the seat.
• Bottom of the post bleeding rust or white chalk. Both are corrosion indicators. The white chalking is aluminum oxidation from constant salt exposure; the rust means a steel bolt or insert is failing inside the post footing.

Replacement Cost & What’s Included

A full KraftMaid fence installation in San Francisco typically runs $4,130 to $10,620. That range covers the variables that actually drive the price of this job: linear footage, whether the existing footing has to be excavated, the slope of the ground (hillside installs run higher), and whether the panels are in stock or must be ordered to spec. A partial repair – say, pulling and resetting four posts, replacing a panel, and re-hanging a gate – usually lands between $700 and $2,800.

Whatever the number ends up being, you’ll get it in writing before we start. That’s The Garrison Standard, and it is non-negotiable. The price on that sheet is a fixed price; it doesn’t move when we hit rock clay at 18 inches or find a decayed footing that wasn’t in the original scope. If the work fails inside one year, the 365-Day Done Right Promise means we come back and make it right at no charge. You won’t have to argue with us about it – it’s in the written guarantee you’ll have in hand when the crew leaves the site.

FAQs